Identification_Information: Citation: Citation_Information: Originator: Emond, A.M. Originator: CGG Originator: Burns, L.E. Originator: Graham, G.R.C. Originator: CGG Land (US) Inc. Publication_Date: 2015 Title: Tok electromagnetic and magnetic airborne geophysical survey data compilation Geospatial_Data_Presentation_Form: digital data Series_Information: Series_Name: Geophysical Report Issue_Identification: GPR 2015-2 Publication_Information: Publication_Place: Fairbanks, Alaska, United States Publisher: Alaska Division of Geological & Geophysical Surveys Online_Linkage: http://dx.doi.org/10.14509/29347 Description: Abstract: The Tok electromagnetic and magnetic airborne geophysical survey data were acquired with a DIGHEMv Electromagnetic (EM) system and a CGG D1344 cesium magnetometer with a Scintrex CS3 cesium sensor. The EM and magnetic sensors were flown at a height of 30 meters (m). In addition the survey recorded data from radar and laser altimeters, a GPS navigation system, 50/60 Hz monitors and a video camera. Flights were performed with an AS-350-B3 Squirrel helicopter at a mean terrain clearance of 60 m along NE-SW (12 degrees) survey flight lines with a spacing of 400 m. Tie lines were flown perpendicular to the flight lines at intervals of approximately 4,800 m. These data were produced under contract between the State of Alaska, Department of Natural Resources, Division of Geological & Geophysical Surveys (DGGS), and CGG Land (U.S.) Inc. Airborne geophysical data for the area were acquired and processed by CGG in 2014 and 2015. The project was funded by the Alaska State Legislature as part of the Alaska Airborne Geophysical/Geological Mineral Inventory Program and the Alaska Strategic and Critical Minerals Assessment Capital Improvement Project. Purpose: The Tok electromagnetic and magnetic airborne geophysical survey data compilation is a product of the Alaska Division of Geological & Geophysical Surveys' (DGGS) Airborne Geophysical/Geological Mineral Inventory (AGGMI) program and the Alaska Strategic and Critical Minerals Assessment Capital Improvement Project. The goal of the Alaska Division of Geological & Geophysical Surveys' (DGGS) Airborne Geophysical/Geological Mineral Inventory (AGGMI) program is to enhance the understanding of Alaska's mineral resources and stimulate private-sector mineral development. The program seeks to delineate mineral zones on Alaska State lands that: (1) have major economic value; (2) can be developed in the short term to provide high-quality jobs for Alaskans; and (3) will provide economic diversification to help offset the loss of Prudhoe Bay oil revenue. Candidate lands for this program are identified on the basis of existing geologic knowledge, land ownership, and nominations from Alaska's geologic community. The AGGMI program and resulting new geologic knowledge are recognized worldwide and have encouraged millions of dollars of venture capital expenditures in the local economies of the surveyed mining districts. These venture capital expenditures have led to discovery and delineation of new mineral resources. The multi-year Strategic and Critical Minerals Assessment Capital Improvement Project (SCMA) was established to determine Alaska's geologic potential for rare-earth elements and other minerals that are essential for our modern, technology-based society. This program began in FY2012 with a data survey and compilation of existing information on rare-earth-element occurrences in Alaska, and expanded significantly in FY2013 to include additional critical minerals, re-analyses of existing samples, and obtaining new field and analytical data, including airborne geophysics. Supplemental_Information: >Project Name: Tok >Contracting Agency: State of Alaska, Department of Natural Resources, Division of Geological & Geophysical Surveys (DGGS) >DGGS Section: Mineral Resources section >Program: Alaska Airborne Geophysical/Geological Mineral Inventory Program and the Alaska Strategic and Critical Minerals Assessment Capital Improvement Program >Funding Source: Alaska State Legislature >Contractor: CGG Land (U.S.) Inc. >Survey Flown By: CGG >CGG Project Number: 14030 >DGGS Contract Manager: Abraham M. Emond >Data Acquisition: Digitally acquired >Line miles (km): 4534.4 miles (7297.4 km) >Data Acquisition: >Start Date (YYYY-MM-DD): 2014-07-30 >End Date (YYYY-MM-DD): 2014-11-13 >Platform: Helicopter >Platform: Model: AS-350-B3 Squirrel >Survey Altitude Model: Mean terrain clearance (height above ground) >Nominal Helicopter Height: 60 metres >Nominal Bird Height: 30 metres >Traverse: Line Azimuth: N12E (heading of 12 degrees) >Traverse: Line Spacing: 1/4 mile (402.3 m) >Tie: Line Azimuth: S102E (heading of 102 degrees) >Tie: Line Spacing: approximately 3 miles (approximately 4828 m) >Border lines: present around all non-parallel and non-perpendicular edges >Magnetics: Magnetometer: Scintrex CS3 cesium sensor, mounted in bird >Electromagnetics: Sensor Model: Dighem(V) >Navigation System: Sensor: Global Positioning System >Navigation System: Sensor: Novatel OEM5-GL2 >Navigation System: Method: Post-flight differential positioning >Additional equipment: Radar and laser altimeters, video camera, and 50/60 Hz monitors > >Operating frequencies used for the Dighem (V) system. > >30-July, 2014 (flts 36025:36027) > >Cx1000 1120 Hz separation = 7.97 m >Cp900 925 Hz separation = 7.98 m >Cx5500 5394 Hz separation = 7.92 m >Cp7200 7456 Hz separation = 7.98 m >Cp56k 55620 Hz separation = 6.32 m > >31-July to 13-November, 2014 (flts 36028:36092, 36103:36120, 37093:37099) > >Cx1000 1120 Hz separation = 7.97 m >Cp900 923 Hz separation = 7.98 m >Cx5500 5458 Hz separation = 7.92 m >Cp7200 7450 Hz separation = 7.98 m >Cp56k 55620 Hz separation = 6.32 m > >FLIGHT AND LINE NAMING > >Example: L11020:29082 > >L = L for transverse(production) T for tie(cross) >1 = Area >1 = Line number digit 1 >0 = Line number digit 2 >2 = Line number digit 3 >0 = Reflight number >: >2 = System number digit 1 >9 = System number digit 2 >0 = Flight number digit 1 >8 = Flight number digit 2 >2 = Flight number digit 3 > >Example: T15021:3089 > >L = T for tie(cross) L for transverse(production) >1 = Area >5 = Line number digit 1 >0 = Line number digit 2 >2 = Line number digit 3 >1 = Reflight number >: >3 = System number digit 1 >0 = Flight number digit 1 >8 = Flight number digit 2 >9 = Flight number digit 3 Time_Period_of_Content: Time_Period_Information: Multiple_Dates/Times: Single_Date/Time: Calendar_Date: 2014 Single_Date/Time: Calendar_Date: 2015 Currentness_Reference: ground condition Status: Progress: complete Maintenance_and_Update_Frequency: as needed Spatial_Domain: Bounding_Coordinates: West_Bounding_Coordinate: -144.399 East_Bounding_Coordinate: -142.943 North_Bounding_Coordinate: 63.337 South_Bounding_Coordinate: 62.854 Keywords: Theme: Theme_Keyword_Thesaurus: ISO 19115 Topic Category Theme_Keyword: geoscientificInformation Theme: Theme_Keyword_Thesaurus: Alaska Division of Geological & Geophysical Surveys Theme_Keyword: Aeromagnetic Theme_Keyword: Aeromagnetic Data Theme_Keyword: Aeromagnetic Map Theme_Keyword: Airborne Geophysical Survey Theme_Keyword: Analytic Signal Theme_Keyword: Apparent Resistivity Contours Theme_Keyword: Apparent Resistivity Data Theme_Keyword: Apparent Resistivity Map Theme_Keyword: Apparent Resistivity Survey Theme_Keyword: Electromagnetic Anomalies Theme_Keyword: Electromagnetic Data Theme_Keyword: Electromagnetic Survey Theme_Keyword: First Vertical Derivative Theme_Keyword: Geophysical Map Theme_Keyword: Geophysical Survey Theme_Keyword: Geophysics Theme_Keyword: Geophysics Search Tag Theme_Keyword: Gridded Data Theme_Keyword: HEM Survey Theme_Keyword: HFEM Survey Theme_Keyword: Magnetic Contours Theme_Keyword: Magnetic Data Theme_Keyword: Magnetic Survey Theme_Keyword: Magnetics Theme_Keyword: Raster Image Place: Place_Keyword_Thesaurus: Alaska Division of Geological & Geophysical Surveys Place_Keyword: Alaska, State of Place_Keyword: Gulkana Quadrangle Place_Keyword: Mentasta Pass Place_Keyword: Mount Hayes Quadrangle Place_Keyword: Nabesna Quadrangle Place_Keyword: Tanacross Quadrangle Place_Keyword: Tok Mining District Place_Keyword: Tok River Stratum: Stratum_Keyword_Thesaurus: Alaska Division of Geological & Geophysical Surveys Stratum_Keyword: Delta Mineral Belt Stratum_Keyword: Denali Fault Access_Constraints: This report, map, and/or dataset is available directly from the State of Alaska, Department of Natural Resources, Division of Geological & Geophysical Surveys (see contact information below). Use_Constraints: Any hard copies or published datasets utilizing these datasets shall clearly indicate their source. If the user has modified the data in any way, the user is obligated to describe the types of modifications the user has made. The user specifically agrees not to misrepresent these datasets, nor to imply that changes made by the user were approved by the State of Alaska, Department of Natural Resources, Division of Geological & Geophysical Surveys. The State of Alaska makes no express or implied warranties (including warranties for merchantability and fitness) with respect to the character, functions, or capabilities of the electronic data or products or their appropriateness for any user's purposes. In no event will the State of Alaska be liable for any incidental, indirect, special, consequential, or other damages suffered by the user or any other person or entity whether from the use of the electronic services or products or any failure thereof or otherwise. In no event will the State of Alaska's liability to the Requestor or anyone else exceed the fee paid for the electronic service or product. Point_of_Contact: Contact_Information: Contact_Organization_Primary: Contact_Organization: Alaska Division of Geological & Geophysical Surveys Contact_Position: GIS Manager Contact_Address: Address_Type: mailing and physical Address: 3354 College Road City: Fairbanks State_or_Province: AK Postal_Code: 99709-3707 Country: USA Contact_Voice_Telephone: (907)451-5020 Contact_Electronic_Mail_Address: dggsgis@alaska.gov Hours_of_Service: 8 am to 4:30 pm, Monday through Friday, except State holidays Data_Set_Credit: Funding for this survey was provided by the Alaska Division of Geological & Geophysical Surveys' (DGGS) Airborne Geophysical/Geological Mineral Inventory (AGGMI) program and Strategic and Critical Minerals Assessment Capital Improvement Project. The Tok geophysical survey was managed by State of Alaska, Department of Natural Resources (DNR), Division of Geological & Geophysical Surveys (DGGS). The survey data was collected and processed by CGG. Cross_Reference: Citation_Information: Originator: Burns, L.E. Originator: Fugro Airborne Surveys Corp. Originator: Stevens Exploration Management Corp. Publication_Date: 2006 Title: Line, grid, and vector data, and plot files for the airborne geophysical survey of the Alaska Highway corridor, east-central Alaska Series_Information: Series_Name: Geophysical Report Issue_Identification: GPR 2006-6 Publication_Information: Publication_Place: Fairbanks, Alaska, United States Publisher: Alaska Division of Geological & Geophysical Surveys Other_Citation_Details: 1 DVD Online_Linkage: http://dx.doi.org/10.14509/14864 Cross_Reference: Citation_Information: Originator: Burns, L.E. Originator: Fugro Airborne Surveys Corp. Originator: Stevens Exploration Management Corp. Publication_Date: 2009 Title: Line, grid, and vector data, and maps for the airborne geophysical survey of the Slate Creek-Slana River Survey, Chistochina mining district, south-central Alaska Series_Information: Series_Name: Geophysical Report Issue_Identification: GPR 2009-1 Publication_Information: Publication_Place: Fairbanks, Alaska, United States Publisher: Alaska Division of Geological & Geophysical Surveys Other_Citation_Details: 18 sheets, 1 DVD, scale 1:63,360 Online_Linkage: http://dx.doi.org/10.14509/19621 Cross_Reference: Citation_Information: Originator: Dashevsky, S.S. Originator: Schaefer, C.F. Originator: Hunter, E.N. Publication_Date: 2003 Title: Bedrock geologic map of the Delta mineral belt, Tok mining district, Alaska Series_Information: Series_Name: Professional Report Issue_Identification: PR 122 Publication_Information: Publication_Place: Fairbanks, Alaska, United States Publisher: Alaska Division of Geological & Geophysical Surveys Other_Citation_Details: 122 p., 2 sheets, scale 1:63,360 Online_Linkage: http://dx.doi.org/10.14509/2923 Data_Quality_Information: Attribute_Accuracy: Attribute_Accuracy_Report: >Apparent resistivity cutoffs: >900 Hz coplanar apparent resistivity cutoff 1325 Ohm-m >1000 Hz coaxial apparent resistivity cutoff 1501 Ohm-m >5500 Hz coaxial apparent resistivity cutoff 8001 Ohm-m >7200 Hz coplanar apparent resistivity cutoff 10750 Ohm-m >56000 Hz coplanar apparent resistivity cutoff 60000 Ohm-m > >Electromagnetic system contract specification: >Frequency; Coil Orientation; Peak-to-Peak Noise Envelope (ppm) > 900 Hz horizontal coplanar 10 > 1000 Hz vertical coaxial 10 > 5500 Hz vertical coaxial 10 > 7200 Hz horizontal coplanar 20 > 56,000 Hz horizontal coplanar 40 > >Magnetic data contract specification: >The in-flight noise envelope will not exceed 0.1 nT in straight and level flight. In rugged areas, the noise level will not exceed 0.5 nT. Logical_Consistency_Report: Data originate from one company using the same contract specifications for all data. The originating coordinate system was retained for all publication products except the KMZ files, which utilize WGS84 geographic coordinates. In some cases we provide values in both UTM NAD27 and geographic WGS84 projections Completeness_Report: >CHANNEL; Valid Data Points; Missing Data Points (dummy value = *) >dep900; 2948902; 734781 >dep7200; 3566682; 117001 >dep56k; 3615182; 68501 >cxsp; 3683647; 36 >cpsp; 3683628; 55 >cppl; 3683598; 85 >mag_diu; 3683260; 423 >mag_lag; 3683260; 423 >mag_raw; 3683290; 393 >mag_rmi; 3683260; 423 >magigrf; 3683260; 423 >res56k; 3651567; 32107 >res7200; 3651567; 32107 >res900; 3651567; 32107 > >Missing magnetic values occur in the databases for the Tok survey area because of the lagging process at the beginning of some lines, and due to despiking. Slow airspeed over steep terrain can cause rapid bird swing and magnetic data spikes that require removal from final data. Missing values in the calculated 'depth' dep56k, dep7200, and dep900 occur where altimeter limits for resistivity calculation are exceeded or where magnetite causes inphase to be negative. Missing apparent resistivity values are generally caused by altitude exceeding the tolerance for meaningful resistivity calculation. > >The GPS gaps are as follows: 1km of interpolated locations occur on a line Flt 36086 L10790 and Flt 36084 L10811 Positional_Accuracy: Horizontal_Positional_Accuracy: Horizontal_Positional_Accuracy_Report: A Novatel OEM5-G2L Global Positioning System was used for navigation. The helicopter position was derived every 0.5 seconds using post-flight differential positioning to a relative accuracy of better than 5 m. Lineage: Source_Information: Source_Citation: Citation_Information: Originator: Akima, H. Publication_Date: 1970 Title: A new method of interpolation and smooth curve fitting based on local procedures Series_Information: Series_Name: Journal of the Association of Computing Machinery Issue_Identification: v. 7, no. 4 Publication_Information: Publication_Place: New York, NY, USA Publisher: Association for Computing Machinery Type_of_Source_Media: paper Source_Time_Period_of_Content: Time_Period_Information: Single_Date/Time: Calendar_Date: 1970 Source_Currentness_Reference: publication date Source_Citation_Abbreviation: Akima, H., 1970 Source_Contribution: geophysical data Source_Information: Source_Citation: Citation_Information: Originator: Fraser, D.C. Publication_Date: 1978 Title: Resistivity mapping with an airborne multicoil electromagnetic system Series_Information: Series_Name: Geophysics Issue_Identification: v. 43 Publication_Information: Publication_Place: Tulsa, OK, United States Publisher: Society of Exploration Geophysicists Type_of_Source_Media: paper Source_Time_Period_of_Content: Time_Period_Information: Single_Date/Time: Calendar_Date: 1978 Source_Currentness_Reference: publication date Source_Citation_Abbreviation: Fraser, D.C., 1978 Source_Contribution: inphase and quadrature components Process_Step: Process_Description: Geophysical data - The airborne geophysical data were acquired between July 30, 2014 through November 13, 2014 with DIGHEM (V) Electromagnetic (EM) systems - Scintrex CS3 cesium magnetometer sensors. The EM and magnetic sensors were flown at a height of 30 meters (m), with the magnetic sensor installed in the EM sensor. In addition, the survey recorded data from radar and laser altimeters, GPS navigation system, 50/60 Hz monitors, thermometer, barometric pressure instrument, and video camera. Flights were performed with one Aerospatiale AS-350-B3 helicopters. All were flown at a nominal mean terrain clearance of 60 m. Survey flight lines were flown at a heading of 345 degrees (NW-SE) with one-quarter mile (402.3 m) line spacing). Tie lines were flown at a heading of 75 degrees (NE-SW), perpendicular to the flight lines, and were spaced at intervals of approximately 4,800 m. Novatel OEM4-G2L Global Positioning Systems were used for navigation and flight path recovery. The helicopter positions were derived every 0.5 seconds (2 Hz); the ground GPS base station data were collected at 1.0 second (1 Hz) intervals. The positional xy data are interpolated from 2 Hz to 10 Hz. The use of the differentially-corrected base station data results in a positional accuracy of better than five meters. Flight path positions were projected onto the Clarke 1866 (UTM zone 7N) spheroid, 1927 North American datum using a central meridian (CM) of 147 degrees, a north constant of 0, and an east constant of 500,000. Source_Used_Citation_Abbreviation: Akima, H., 1970 Process_Date: 2014 Process_Step: Process_Description: Total magnetic field data - The total magnetic field data were acquired with a sampling interval of 0.1 seconds. The raw magnetic data (channel 'mag_raw') were (1) corrected for measured system lag (resulting in channel 'mag_lag'), (2) corrected for diurnal variations by subtraction of the digitally recorded base station magnetic data (resulting in channel 'mag_diu'), (3) adjusted for regional variations (by subtracting IGRF model 2010, updated for date of flight and elevation variations), (4) leveled to the tie line data resulting in the final residual magnetic intensity, (5) manually leveled with final small microleveling (resulting in channel 'mag_rmi'), and (6) increased by a constant IGRF average value to restore the mag_rmi values to a total magnetic field channel (resulting in channel 'magigrf'). 'Mag_RMI' and 'MagIGRF' were then interpolated onto a regular 80-m grid using a modified Akima (1970) technique. Process_Date: 2014 Process_Step: Process_Description: Magnetic and derivative magnetic grids - Three different algorithms were applied to the total magnetic field 80 m grid, resulting in three magnetic derivative grids. The analytic signal grid is the total amplitude of all directions of magnetic gradient calculated from the sum of the squares of the three orthogonal gradients. Mapped highs in the calculated analytic signal of the magnetic parameter locate the anomalous source body edges and corners (e.g., contacts, fault/shear zones, basement fault block boundaries or lithologic contacts, etc.). Analytic signal maxima are located directly over faults and contacts, regardless of structural dip, and independently of the direction of the induced and/or remnant body magnetizations. The calculated magnetic tilt grid is the angle between the horizontal gradient and the total vertical gradient, and is useful for identifying the depth and type of magnetic source. The tilt angle is positive over the source, crosses through zero at, or near, the edge of a vertical sided source, and is negative outside the source zone. It has the added advantage of responding equally well to shallow and deep sources and is able to resolve deeper sources that may be masked by larger responses caused by shallower sources. The first vertical derivative grid was calculated using a fast Fourier transform (FFT)-based frequency-domain filtering algorithm. The vertical gradient algorithm enhances the response of magnetic bodies in the upper 500 m and attenuates the response of deeper bodies. The resulting (calculated) vertical gradient grid provides better definition and resolution of near-surface magnetic units and helps to identify weak magnetic features that may not be evident in the total field data. All magnetic and derivative magnetic grids were then resampled from the 80-m cell size down to a 25-m cell size using a modified Akima (1970) technique to produce the maps and final grids contained in this publication. When resampling the grids to a 25-m cell size, the original grids are scanned to determine the minimum and maximum values which the new grids are then limited to, avoiding extreme extrapolation errors between lines. Process_Date: 2014 Process_Step: Process_Description: Inphase and quadrature components - The DIGHEM (V) EM systems measured inphase and quadrature components at five frequencies. Two vertical coaxial-coil pairs operated at nominal frequencies of 1000 and 5500 Hz while three horizontal coplanar-coil pairs operated at 900, 7200, and 56,000 Hz. Receiver - transmitter geometry and actual operating frequencies are documented in the metadata and data. Source_Used_Citation_Abbreviation: Fraser, D.C., 1978 Process_Date: 2014 Process_Step: Process_Description: Apparent resistivity - EM data were sampled at 0.1 second intervals. The EM system responds to bedrock conductors, conductive overburden, and cultural sources. The EM inphase and quadrature data were drift-corrected using base level data collected at high altitude (areas of no signal). Along-line filters are applied to the data to remove spheric spikes. The data were inspected for variations in phase, and a phase correction was applied to the data if necessary. The apparent resistivity and depth were then calculated from the inphase and quadrature data for all coplanar frequencies. The calculation used the pseudo-layer (or buried) half-space model defined by Fraser (1978). This model consists of a resistive layer overlying a conductive half-space. The apparent depth is defined as the sensor-source distance minus the measured altitude of the sensor above the ground. The apparent depth channels estimate the depth below surface of a conductive half-space and are the apparent thickness of the overlying resistive layer. The apparent depth (or thickness) parameter will be positive when the upper layer is more resistive than the underlying material, in which case the apparent depth may be quite close to the true depth assuming it is a buried halfspace and altimeter is correct. The apparent depth will be negative when the upper layer is more conductive than the underlying material, and will be zero when a homogeneous half-space exists. The apparent depth parameter must be interpreted cautiously because it will contain any errors that might exist in the measured altitude of the EM bird (e.g., as caused by a dense tree cover). Manual leveling of the inphase and quadrature of each coil pair, based on the resistivity data and comparisons to the data from the other frequencies, was performed. Automated micro-leveling is carried out in areas of low signal. The EM data were interpolated onto a regular 80-m grid using a modified Akima (1970) technique. The resulting grids were subjected to a 3x3 Hanning filter and resampled to a 25-m cell size before contouring and map production. When re-sampling the grids to a 25-m cell size, the original grids are scanned to determine the minimum and maximum values which the new grids are then limited to, avoiding extreme extrapolation errors between lines. Process_Date: 2014 Process_Step: Process_Description: Digital elevation/terrain model - The digital elevation/terrain model was produced from the differentially corrected GPS-Z data (channel 'GPSZ' in line data) and the laser altimeter data measured in the bird (channel 'ALTLAS_BIRD' included in the same files). Both the GPSZ and ALTLAS_BIRD data were checked for spikes, which were removed manually. The ALTLAS_BIRD data were despiked and then filtered using a 13 median filter, followed by a 13 Hanning filter. The corrected altimeter data were then subtracted from the GPSZ data to produce profiles of the height above mean sea level along the survey lines. The data were manually leveled to remove any errors between lines. After all leveling, the data were DC shifted to match the local maps, in this case, NAD27. The 80-m DTM grid was then resampled to a 25-m cell size to produce the DTM grid contained in this publication. Process_Date: 2014 Process_Step: Process_Description: Map overlays - Fugro Airborne Surveys downloaded the Alaska PLSS Section Grid shapefile in fall 2008 and subset this in-house version to roughly fit the map sheets for this publication using MapInfo Professional. CGG modified the formatting of the file using AutoCad, changing township and range line widths and colors, and added township and range labels. The modified file was then used as overlays on maps without topography. Process_Date: 2014 Process_Step: Process_Description: Geographically registered gridded data - All grids with 25 m cell size were converted to Geotiffs and KMZs using CGG's specialized software. Process_Date: 2015 Process_Step: Process_Description: Print files - The HPGL/2 files were created with HP Designjet T1300ps HPGL driver. The Adobe Acrobat format files were created with Adobe Acrobat Distiller v9.0 from Postscript files. Process_Date: 2015 Process_Step: Process_Description: Boundary polygon - The boundary polygon was generated by loading the final line data in Geosoft Oasis montaj v8.4. No tie (control) line data were used in this process. The final magnetic data was gridded using the Minimum Curvature option with the following settings: grid cell size = 1/5 of line spacing, blanking distance = double the line spacing, cells to extend beyond data = 0. The polygon file was created using Grid Outline tool with edge resolution = 1. The polygon file was exported to ERSI shapefile. Process_Date: 2015 Process_Step: Process_Description: Discrete anomalous EM responses (EM anomalies) were computer picked from the electromagnetic data set and classified by type and grade. Line and polygon features of the electromagnetic and magnetic data were identified by contractor staff. EM anomalies are presented on map and profile data and are available in ASCII file format. These features are named and stored in geographically registered formats. More information about these products is found in the project report. Process_Date: 2015 Spatial_Reference_Information: Horizontal_Coordinate_System_Definition: Planar: Grid_Coordinate_System: Grid_Coordinate_System_Name: Universal Transverse Mercator Universal_Transverse_Mercator: UTM_Zone_Number: 7 Transverse_Mercator: Scale_Factor_at_Central_Meridian: 0.999600 Longitude_of_Central_Meridian: -141 Latitude_of_Projection_Origin: 0 False_Easting: 500000.000000 False_Northing: 0 Planar_Coordinate_Information: Planar_Coordinate_Encoding_Method: coordinate pair Coordinate_Representation: Abscissa_Resolution: .01 Ordinate_Resolution: .01 Planar_Distance_Units: Meters Geodetic_Model: Horizontal_Datum_Name: World Geodetic System of 1984 Ellipsoid_Name: WGS 84 Semi-major_Axis: 6378137 Denominator_of_Flattening_Ratio: 298.257223563 Entity_and_Attribute_Information: Detailed_Description: Entity_Type: Entity_Type_Label: ascii_data Entity_Type_Definition: ASCII format final line data with readme files; note: these data are provided in both UTM NAD27 and geographic WGS84 projections Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: ascii_data Detailed_Description: Entity_Type: Entity_Type_Label: databases_geosoft Entity_Type_Definition: Geosoft format database of final line data with readme files; note: these data are provided in both UTM NAD27 and geographic WGS84 projections. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: databases_geosoft Detailed_Description: Entity_Type: Entity_Type_Label: documents Entity_Type_Definition: Field operations report, gridded data explanations, survey background information, processor notes. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: documents Detailed_Description: Entity_Type: Entity_Type_Label: grids_ermapper Entity_Type_Definition: Geographically registered gridded data, ER Mapper ERS format. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: grids_ermapper Detailed_Description: Entity_Type: Entity_Type_Label: grids_geosoft Entity_Type_Definition: Geosoft-format binary grids, these grids can be viewed in ESRI ArcMap using a free plugin from Geosoft. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: grids_geosoft Detailed_Description: Entity_Type: Entity_Type_Label: images_registered Entity_Type_Definition: GeoTiff format images of all gridded data. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: images_registered Detailed_Description: Entity_Type: Entity_Type_Label: kmz Entity_Type_Definition: Google Earth kmz files of of all gridded data; note: these files use the WGS84 datum. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: kmz Detailed_Description: Entity_Type: Entity_Type_Label: maps_pdf_format Entity_Type_Definition: Printable maps in pdf format. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: maps_pdf_format Detailed_Description: Entity_Type: Entity_Type_Label: maps_prn_format Entity_Type_Definition: Printable maps in HPGL/2 printer file format with extension .prn. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: maps_prn_format Detailed_Description: Entity_Type: Entity_Type_Label: vector_data Entity_Type_Definition: Line path, data contours, and survey boundary in ESRI shape file (SHP) and Autocad (2000) DXF formats. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: vector_data Detailed_Description: Entity_Type: Entity_Type_Label: video_flightpath Entity_Type_Definition: Downward looking video to verify position and record ground conditions. Video synchronized with data. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: video_flightpath Detailed_Description: Entity_Type: Entity_Type_Label: profiles_stacked Entity_Type_Definition: Electromagnetic and magnetic data profiles with EM anomalies. Entity_Type_Definition_Source: CGG Entity_Attribute_Layer_Name: profiles_stacked Distribution_Information: Distributor: Contact_Information: Contact_Organization_Primary: Contact_Organization: Alaska Division of Geological & Geophysical Surveys Contact_Address: Address_Type: mailing and physical Address: 3354 College Road City: Fairbanks State_or_Province: AK Postal_Code: 99709-3707 Country: USA Contact_Voice_Telephone: (907)451-5020 Contact_Facsimile_Telephone: (907)451-5050 Contact_Electronic_Mail_Address: dggspubs@alaska.gov Hours_of_Service: 8 am to 4:30 pm, Monday through Friday, except State holidays Contact_Instructions: Please view our website (http://www.dggs.alaska.gov) for the latest information on available data. Please contact us using the e-mail address provided above when possible. Resource_Description: GPR 2015-2 Distribution_Liability: The State of Alaska makes no expressed or implied warranties (including warranties for merchantability and fitness) with respect to the character, functions, or capabilities of the electronic data or products or their appropriateness for any user's purposes. In no event will the State of Alaska be liable for any incidental, indirect, special, consequential, or other damages suffered by the user or any other person or entity whether from the use of the electronic services or products or any failure thereof or otherwise. In no event will the State of Alaska's liability to the Requestor or anyone else exceed the fee paid for the electronic service or product. Standard_Order_Process: Non-digital_Form: DGGS publications are available as free online downloads or you may purchase paper hard-copies or digital files on CD/DVD or other digital storage media by mail, phone, fax, or email from the DGGS Fairbanks office. To purchase this or other printed reports and maps, contact DGGS by phone (907-451-5020), e-mail (dggspubs@alaska.gov), or fax (907-451-5050). Payment accepted: Cash, check, money order, VISA, or MasterCard. Turnaround time is 1-2 weeks unless special arrangements are made and an express fee is paid. Shipping charge will be the actual cost of postage and will be added to the total amount due. Contact us for the exact shipping amount. Fees: Contact DGGS for current pricing Standard_Order_Process: Digital_Form: Digital_Transfer_Information: Format_Name: GeoTiff, ESRI shapefile, Geosoft binary grid (GRD), Microsoft Office documents, PDF, ER Mapper ERS, ASCII text files (including CSV), Geosoft ASCII grid (GXF), Geosoft database, AutoCAD DXF, Geosoft plot file (PLT), Printer files (HPP, PRN, or other), digital images (multiple formats), digital video (multiple formats), Geosoft ASCII XYZ, Geosoft ASCII files (PLY, i0, EXP), and KMZ Digital_Transfer_Option: Online_Option: Computer_Contact_Information: Network_Address: Network_Resource_Name: http://dx.doi.org/10.14509/29347 Fees: Free download Technical_Prerequisites: Requisite software varies according to the file format. Possible software requirements include, but are not limited to: Geosoft Oasis montaj (full version and viewer), INTREPID geophysical software, ESRI Arc GIS products, MapInfo, Global Mapper, UltraEdit, NotePad ++, Microsoft Office or open source office software, Adobe Reader, Lerup PrintFile, Google Earth, ER Mapper Metadata_Reference_Information: Metadata_Date: 20151229 Metadata_Contact: Contact_Information: Contact_Organization_Primary: Contact_Organization: Alaska Division of Geological & Geophysical Surveys Contact_Position: Metadata Manager Contact_Address: Address_Type: mailing and physical Address: 3354 College Road City: Fairbanks State_or_Province: AK Postal_Code: 99709-3707 Country: USA Contact_Voice_Telephone: (907)451-5020 Metadata_Standard_Name: FGDC Content Standard for Digital Geospatial Metadata Metadata_Standard_Version: FGDC-STD-001-1998 Metadata_Use_Constraints: If the user has modified the data in any way they are obligated to describe the types of modifications they have performed in the supporting metadata file. User specifically agrees not to imply that changes they made were approved by the Alaska Department of Natural Resources or Division of Geological & Geophysical Surveys. Metadata_Extensions: Online_Linkage: http://www.dggs.alaska.gov/metadata/dggs.ext Profile_Name: dggs metadata extensions